Delta 28-299A Betriebsanleitung Seite 11
- Seite / 77
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4 Electrical Installation
4.1 Electrical Installation
4.1.1 Control Wiring
The soft starter can be controlled in three ways:
•
•
using the buttons on the LCP
•
via remote inputs
•
via a serial communication link
The MCD 500 will always respond to a local start or stop command (via the H
Hand On
and O
Off
buttons on the LCP). Pressing the
Auto On
button selects remote control (the MCD 500 will accept commands from the remote inputs). In remote mode, the Auto
On LED will be on. In local mode, the Hand On LED will be on if the MCD 500 is starting or running and the Off LED will be on if
the MCD 500 is stopped or stopping.
4.1.2 Control Terminals
Control terminations use 2.5 mm
2
plug-in terminal blocks. Different models require control voltage to different terminals:
CV1 (24 VAC/VDC) A5, A6
CV2 (110 - 120 VAC) A5, A6
CV2 (220 - 240 VAC) A4, A6
NOTE
If you are not using a thermistor, do not short terminals 05,
06.
All control terminals and relay terminals comply with SELV
(Protective Extra Low Voltage). This protection does not
apply to grounded Delta leg above 400V.
To maintain SELV, all connections made to the control
terminals must be PELV (eg. thermistor must be reinforced/
double insulated from motor).
NOTE
SELV offers protection by way of extra low voltage.
Protection against electric shock is ensured when
the
electrical supply is of the SELV type and the installation is
made as described in local/national r
egulations on SELV
supplies.
NOTE
Galvanic (ensured) isolation is obtained by fulfilling
requirements for higher isolation and by provid
ing the
relevant creepages/clearance distances. These requirements
are described in the IEC61140 standa
rd.
The components that make up the electrical isolation also
comply with the requirements for higher i
solation and the
relevant test as described in IEC61140.
Electrical Installation MCD 500 Operating Instruction
10 MG.17.K3.02 - VLT
®
is a registered Danfoss trademark
44
- Operating Instructions 1
- MG.17.K3.02 - VLT 2
- 5 Application Examples 3
- 6 Operation 3
- 7 Programming 4
- 9 Troubleshooting 5
- 10 Specifications 5
- 1 Safety 6
- 2 Introduction 7
- 177HA382.11 8
- 3 Installation 9
- 177HA514.10 10
- 4 Electrical Installation 11
- 4.1.3 Remote Inputs 12
- 4.1.4 Serial Communication 12
- 4.1.5 Earth Terminal 12
- 177HA542.11 13
- 4.1.7 Motor Connection 14
- 4.2 In-Line Installation 14
- 177 HA4 31.11 15
- 177HA500.11 16
- 4.4 Current Ratings 17
- Start Time (seconds) 19
- Starts Per Hour 19
- 4.6 Bypass Contactor 22
- 4.7 Main Contactor 22
- 4.8 Circuit Breaker 22
- 4.9 Power Factor Correction 22
- 4.10 Fuses 23
- 4.10.1 Power Supply Fuses 23
- 4.10.4 Ferraz Fuses - HSJ 25
- 4.11 Schematic Diagrams 28
- 177HA426.11 29
- 5.3 Starting Modes 31
- 5.3.1 Constant Current 31
- 5.3.2 Current Ramp 31
- Voltage (% full voltage) 32
- 177HA511.10 33
- 5.6 Inside Delta Operation 34
- 5.7 Typical Start Currents 34
- 177HA522.10 36
- 177HA523.10 37
- 5.10 Emergency Run Operation 38
- 5.11 Auxiliary Trip Circuit 39
- 5.12 Soft Braking 40
- 5.13 Two Speed Motor 41
- 6.2 Control Methods 44
- 6.3 Local Control Buttons 44
- 6.4.8 Date and Time (S8) 46
- 6.4.9 SCR Conduction Bargraph 46
- 6.4.10 Performance Graphs 46
- 7.2 Quick Menu 48
- 7.2.1 Quick Setup 48
- 7.2.2 Application Setups 49
- 7.2.3 Loggings 50
- 7.3 Main Menu 50
- 7.3.1 Parameters 50
- 7.3.2 Parameter Shortcut 50
- 7.3.3 Parameter List 51
- 7.4 Primary Motor Settings 52
- 7.4.1 Brake 53
- 7.5 Protection 53
- 7.5.1 Current Imbalance 53
- 7.5.2 Undercurrent 53
- 7.5.4 Frequency Trip 54
- 7.6 Inputs 54
- * [00:00 - 30:00 55
- 7.7 Outputs 56
- 7.7.1 Relay A Delays 56
- 7.7.2 Relays B and C 56
- 7.7.4 Motor Temperature Flag 57
- 7.7.5 Analog Output A 57
- 7.8 Start/Stop Timers 57
- 7.9 Auto-Reset 58
- 7.9.1 Auto-Reset Delay 58
- 7.10 Secondary Motor Set 58
- 7.11 Display 60
- 7.11.2 Performance Graphs 61
- 7.12 Restricted Parameters 61
- * [100 - 2000 62
- 8.1 Set Date and Time 63
- 8.2 Load/Save Settings 63
- 8.3 Reset Thermal Model 63
- 8.4 Protection Simulation 63
- 8.5 Output Signal Simulation 64
- 8.6 Digital I/O State 64
- 8.7 Temp Sensors State 64
- 8.8 Alarm Log 64
- 8.8.1 Trip Log 64
- 8.8.2 Event Log 65
- 8.8.3 Counters 65
- 9.2 General Faults 69
- Symptom Probable Cause 70
- 10.1 Accessories 72
- 10.1.1 Communication Modules 72
- 10.1.2 PC Software 73
- 10.1.3 Finger Guard Kit 73
- *MG17K302* 77
Verwandte Produkte und Handbücher für Kreissägen Delta 28-299A
Kreissägen Delta 36-655 Bedienerhandbuch
(24 Seiten)
(24 Seiten)
Kreissägen Delta 20-140 Bedienerhandbuch
(16 Seiten)
(16 Seiten)
Kreissägen Delta 36-714 Bedienerhandbuch
(80 Seiten)
(80 Seiten)
Kreissägen Delta 20-330 Bedienerhandbuch
(64 Seiten)
(64 Seiten)
Kreissägen Delta 36-725 Bedienerhandbuch
(64 Seiten)
(64 Seiten)
Kreissägen Delta 36-465 Bedienerhandbuch
(36 Seiten)
(36 Seiten)
Kreissägen Delta CL180CS Bedienerhandbuch
(17 Seiten)
(17 Seiten)
Kreissägen Delta 40-690 Bedienerhandbuch
(40 Seiten)
(40 Seiten)
Kreissägen Delta 36-5000 Bedienerhandbuch
(100 Seiten)
(100 Seiten)
Kreissägen Delta 36-325C Bedienerhandbuch
(28 Seiten)
(28 Seiten)
Kreissägen Delta 20-140 Bedienungsanleitung
(8 Seiten)
Kreissägen Delta 36-648 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
Kreissägen Delta 36-600 Bedienungsanleitung
(15 Seiten)
(15 Seiten)
Kreissägen Delta 36-978 Bedienerhandbuch
(37 Seiten)
(37 Seiten)
Kreissägen Delta 34-814 Bedienerhandbuch
(28 Seiten)
(28 Seiten)
Kreissägen Delta 36-902 Bedienerhandbuch
(20 Seiten)
(20 Seiten)
Kreissägen Delta MS210 Bedienungsanleitung
(35 Seiten)
(35 Seiten)
Kreissägen Delta 36-075 Bedienungsanleitung
(28 Seiten)
(28 Seiten)
Kreissägen Delta 20-140 Bedienungsanleitung
(5 Seiten)
(5 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern