Delta DP400 Bedienerhandbuch Seite 1

INSTRUCTION MANUAL16½" Floor Model Drill Press(Model DP400)PART NO. A10352 - 03-28-05Copyright © 2005 Delta MachineryESPAÑOL: PÁGINA 23To learn m

10ASSEMBLYFOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THEMACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE

THE PLYWOOD BASE MUST BESECURED TO THE FLOOR OR SUPPORTINGSURFACE IF THERE IS ANY TENDENCY OF THEDRILL PRESS TO VIBRATE, SLIDE OR WALKDURING NORMAL OP

12Fig. 99. Insert table (H) Fig. 9, into hole in table bracket asshown.Fig. 1010. Thread table locking lever (J) Fig. 10, into hole infront of table b

13Fig. 1414. IMPORTANT: Make certain the spindle taper (O) Fig.14, and tapered hole in chuck (P) are clean and free ofany grease, lacquer or rust prev

1418. Align the two holes in the lamp bracket (A) Fig. 17,with the two holes (B) on the side of the drill press head.Fig. 1720. Align the two holes in

STARTING AND STOPPINGDRILL PRESSThe switch (A) Fig. 20, is located on the front of the drillpress head. To turn the drill press “ON” move the switchup

16Fig. 24CE3. The table can be tilted right or left by pulling out andremoving table alignment pin (C) Fig. 24. NOTE: If pin (C)is difficult to remove

17SPINDLE SPEEDSTwelve spindle speeds are available on the drill press. Fig. 27, illustrates which steps of the pulleys the belts must beplaced to obt

18DRILLING HOLES TO DEPTHWhere a number of holes are to be drilled to exactly thesame depth, a depth stop is provided and is used asfollows:DISCONNECT

19Fig. 32Your drill press is to be used with drill bits with a shank of5/8" or less in diameter. The following will give theinexperienced operato

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20BORING IN WOODTwist drills, although intended for metal drilling, may also be used for boring holes in wood. However, machine spur bitsare generally

21TROUBLESHOOTINGFor assistance with your machine, visit our website at www.deltamachinery.com for a list of service centers or callthe DELTA Machiner

22MAINTENANCEPARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5ADDITIONAL SPECIFIC SAFETY RULESFAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.1. DO NOT OPERATE THIS MACHINE until it iscompletely assem

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

7EXTENSION CORDSUse proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong groun

8FOREWORDDelta ShopMaster DP400 is a 16½" drill press with a 120/240 V, 3/4 H.P. induction motor, a flexible work lamp and atilting table with c-

9CARTON CONTENTS12345678910111213141516171820212219Fig. 21. Drill Press Head2. Table3. Table Bracket and Column4. Light5. Base6. Chuck7. Handle (3)8.