Delta 28-206 Bedienerhandbuch

INSTRUCTION MANUAL14" Band Saws(Models 28-206, 28-276)PART NO. 906452 - 08-16-02Copyright © 2002 Delta MachineryESPAÑOL: PÁGINA 25To learn more a

10Fig. 814. Align the holes in the base (A) Fig. 8, with the holesin the two sides (B).15. Insert a M8x1.25x16mm hex head flange screwthrough the hole

11MODEL 28-276 OPEN STAND ASSEMBLYWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLE

1214. Align the four holes in the short brace (A) Fig. 14,with the four holes in the two legs (B).15. Insert a M8x1.25x16mm carriage head bolt through

13BAND SAW ASSEMBLYWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ

14ATTACHING THE TABLE TOTHE SAWFig. 191. Remove the band saw blade.2. Align the two table studs (A) Fig. 19, in the bottom ofthe table, with the two h

15OPERATING CONTROLS AND ADJUSTMENTSSTARTING ANDSTOPPING SAWThe power switch is located on the left side of themachine. To turn the machine “ON”, push

16ADJUSTING THE TABLE STOPThe tool is equipped with an adjustable table stop (A)Fig. 26 that allows the table to be set at 90 degrees tothe blade.Tilt

17TRACKING THE BLADECAUTION: DISCONNECT MACHINE FROM POWERSOURCE.IMPORTANT: Before tracking the blade, make sure thatthe blade guides and blade suppor

185. Two set screws (B) Fig. 35 hold the upper bladeguides (A) in place. Loosen the set screws (B) to movethe guides (A). Place them as close as possi

19OPERATIONSBefore starting the machine, insure that all adjustments are properly made and the guards are in place. Turn the upperwheel by hand to mak

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

20TROUBLESHOOTING GUIDEIn spite of how well a band saw is maintained, problems can occur. The following troubleshootingguide will help you solve the m

21Trouble: BLADE WILL NOT TRACK.Probable Cause Remedy1. Blade too loose 1. Adjust tension2. Upper wheel not properly adjusted. 2. Adjust upper wheel.3

22BAND SAW BLADESA band saw blade is a delicate piece of steel that is subjected to tremendous strain. You canobtain long use from a band saw blade if

23NOTES

Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machine accessory whichin

3ADDITIONAL SAFETY RULES FORBAND SAWSWARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.SAVE THESE INSTRUCTIONS.Refer to the

4POWER CONNECTIONSA separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord whichhas a 3-prong grounding type plug a

6BAND SAW PARTSFig. 21. Band Saw2. Motor3. Table4. Table Insert5. Belt6. Motor Mounting Plate7. M8x1.25x80mm (4) (for assembling saw to stand)1234568.

7MODEL 28-206 ENCLOSED STAND PARTS1. Base (2)2. Side (2)3. Stand Top4. Door (2)5. Pulley Guard6. M8x1.25x100mm Hex Head Screw7. M8x1.25x16mm Hex Head

8MODEL 28-276 OPEN STAND PARTS1. Legs (4)2. Stand Top3. Long Brace (2)4. Short Brace (2)5. Upper Pulley Guard 6. Lower Pulley Guard7. M8x1.25x80mm Hex

9MODEL 28-206 ENCLOSED STAND ASSEMBLYWARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEM