Delta 601T040 Installationsanleitung PDF herunterladen (Seite 5)

Page 5

204499 Rev. A

TROUBLE SHOOTING GUIDE

Check to ensure faucet was installed

according to the M&I sheet.

Test for operation. If unit does not

operate:

If faucet shuts off due to interference:

If the faucet does not work properly, follow the steps below in order.

Step 1

Note: See instructions on pages 1 to 4.

Check to be sure that white sensor wire is firmly connected to the thin

capacitance tab, and that the nut and washer are firmly connected to

the underside of the counter top. See Fig. 1 on page 2.

Check to be sure power cable is properly secured in fitting.

Check to be sure batteries are fresh and properly installed.

Check two wires to solenoid to be sure they are connected correctly.

Check to be sure water supply is turned on.

When the faucet detects an object for longer than 45 seconds, or if

faucet self-cycles for 4 times within 15 seconds, it will automatically shut

off. This will be followed by 3 quick beeps which indicate that calibration

is about to take place. The faucet will then enter calibration per step 7b.

Once calibration takes place (with no user present) the faucet will return

to regular operation.

Faucet makes a beeping noise.

(Different from re-calibration in step 1):

Step 2

BATTERY POWERED: Faucet beeps twice when turning off:

indicates batteries are low and need to be replaced (1500 cycles or 2

weeks left). Faucet beeps continuously when hands in front of

spout and no water: faucet locked out because batteries are too low.

HARDWIRE: Check voltage from converter and transformer. It should

be approximately 6.4 volts DC coming from converter to the driver

board.

Replace batteries.

Replace Hardwire

converter 060683A, if

required.

The faucet stops working. No water flow.

Check the function of the solenoid.

Step 3

The solenoid should “click” when activated.

Clean as required.

Correct as required.

If there is a

clicking sound:

If no clicking

sound:

This indicates that both the sensor and the solenoid are functioning.

Ensure inlet screen on solenoid is not plugged with debris.

Check the incoming water supply. Turned on, proper pressure and

volume, etc.

Check for a pressure lock between the mixing valve and the solenoid.

Turn off the water supply and undo the connection to the inlet of the

solenoid, this will eliminate any built-up pressure.

Then activate sensor and test fire the solenoid.

If after above there is no clicking sound;

Defective solenoid.

Replace 060910A

Solenoid.

If faucet does not activate or works

erractically:

Step 4

If after completion of all above steps, the valve still does not function correctly; Call Technical Service for further assistance at 1-800-387-8277.

Step 5

Check for electrical interference.

Check for interference from other electrical devices within close

proximity to the spout or battery box. Devices such as other infrared

devices, transformers, etc.

Excessive water on the counter top may lead to an overly sensitive

faucet. Wipe water off, re-calibrate the faucet.

Re-calibrate the unit by disconnecting the batteries for 10 seconds, then

reconnecting. Follow steps 7a and 7b of the Installation and Set-Up

Instructions.

BATTERY and HARDWIRE POWERED: When battery connection is

touched, it trips the electronics and turns on the solenoid.

Call Technical Service if

any such conditions

found. 1-800-387-8277.

This Delta Commercial faucet is designed and engineered in accordance with the highest quality and performance standards. With

proper care, it will give you years of trouble free service. Care should be given to the cleaning of this product. Although the chrome

finish is extremely durable, it can be DAMAGED by ACIDIC CLEANERS (i.e., cleaners designed specifically for vitreous china

lavatories and water closets), HARSH ABRASIVES or POLISH. To clean, simply wipe the surface with a damp cloth and blot dry with

a soft towel.

CARE INSTRUCTIONS

BATTERY POWERED: Check to ensure all batteries are inserted

correctly.

HARDWIRE: Check voltage from converter to transformer.

Ensure battery polarities

are correct and that

voltage is sufficient -

around 6 volts.

Continuous beeping tone upon power-up:

Water runs non stop when batteries are

disconnected:

When disconnecting the

power, grab the battery

clip and wait for at least

one full second before

disconnecting it.

Solenoid will shut off

after power disconnected.

1 2 3 4 5 6

Kommentare zu diesen Handbüchern

Keine Kommentare

Delta 601T040 Installationsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Wasserhähne Delta 601T040