Delta 33-830 Bedienerhandbuch

10″″Professional Radial Arm Saw(Model 33-830)INSTRUCTION MANUALPART NO. 424-12-651-0031 (019)Copyright © 2001 Delta MachineryESPAÑOL: PÁGINA 29To lear

10Fig. 11Fig. 12Fig. 13Fig. 14REMOVING BLADE ANDBLADE GUARD FROM SAW1. DISCONNECT TOOL FROM POWER SOURCE.2. Loosen blade guard clamp knob (A) Fig. 11,

11Fig. 15Fig. 16Fig. 17Fig. 18ASSEMBLING TRACK ARMCLAMP LEVER1. Assemble track arm clamp lever (A) Fig. 15, bythreading into clamp lock nut (B).ASSEMB

125. Using a combination square (M) Figs. 19 and 20,check the left and right front edge of table board (A) tomake certain both sides are the same dist

13Fig. 24Fig. 25Fig. 26Fig. 28Fig. 2710. Loosen track arm clamp handle (Y) Fig. 24. NOTE:Track clamp handle (Y) has left handed threads. Pressdown on

14Fig. 29Fig. 30Fig. 31Fig. 32ASSEMBLINGTABLE BOARD CLAMPSAND TABLE BOARDS1. Locate table board clamps (A) Fig. 29, and insertone clamp into each of t

15Fig. 33Fig. 34Fig. 35Fig. 365. Loosen cutting-head clamp knob (S) Fig. 33, andslide cutting-head (T) the entire length of track arm (A) asshown to d

16Fig. 37Fig. 38Fig. 39Fig. 40REMOVING “HEELING”IN SAW BLADE CUTEven though the cutting-head travel may be perfectlyaligned at 90 degrees to the fence

17Fig. 41Fig. 42Fig. 435. Place a square (D) Fig. 41, on the table and againstthe saw blade, as shown, and check to see if the bladeis square with the

18Fig. 44Fig. 45Fig. 46Fig. 47ASSEMBLING BLADE ANDBLADE GUARD TO MACHINE1. DISCONNECT TOOL FROM POWER SOURCE. USEONLY 10″″BLADES WITH 5/8″″ARBOR HOLES

19FASTENING SAW TO THE FLOORIf during operation there is any tendency for the saw to tip over, slide, or walk on the supporting surface, thesaw should

2GENERAL SAFETY RULESWoodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain ha

20Fig. 62Fig. 63ADJUSTING BALLBEARINGS AGAINST TRACKThe cutting-head (C) Fig. 61, is suspended from fourpre-loaded, lubricated, shielded ball bearings

21Fig. 64Fig. 65Fig. 665. Using a 3/16″ Allen wrench (J) Fig. 64, turn adjustmentscrews (K) Figs. 61 and 64 to remove all “play.” NOTE: DONOT OVERTIGH

22Fig. 67Fig. 68Fig. 69Fig. 703. Rotate hex bolt (B) Fig. 67, in the desired directionwhich the handle needs to be turned.4. Push hex bolt (B) Fig. 67

2323Fig. 71Fig. 72Fig. 73POSITIVE STOP YOKE INDEXYoke index lever (A) Fig. 71, activates a positive stopwhich positions the cutting-head in the cross-

CROSS-CUT STOPA block of wood placed at (B) Fig. 74A clamped to thetrack arm with a small “C” clamp will preventunnecessary travel (T) of the cutting-

25COMPOUNDMITER CUTTINGCompound miter cutting is performed in the samemanner as miter cutting except the saw blade is also tiltedto cut a bevel. The s

26CONSTRUCTING A PUSH STICKWhen ripping work less than 4 inches wide, a push stick should be used to complete the feed and could easily bemade from sc

27Printed in U.S.A.PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced

28NOTES

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER®,INNOVATION THAT WORKS®, JETST

3ADDITIONAL SAFETY RULES FOR RADIAL ARM SAWS1. READ AND UNDERSTAND THE INSTRUCTIONMANUAL BEFORE OPERATING THIS TOOL.2. DO NOT OPERATE THIS TOOL unti

4POWER CONNECTIONSA separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should beprotected wi

5Fig. CGROUNDED OUTLET BOXGROUNDINGMEANSADAPTERFig. DGROUNDED OUTLET BOXCURRENTCARRYINGPRONGSGROUNDING BLADEIS LONGEST OF THE 3 BLADESFig. EFig. FCHAN

6FUNCTIONAL DESCRIPTIONFOREWORDDelta Model 33-830 is a 10" (254mm) Professional Radial Arm Saw with maximum cutting capacity of 16" (406mm)c

7Fig. 4Fig. 51. 10″ Professional RadialArm Saw2. Left and righttable supports3. 5/16-18 x 5/8″ CarriageHead Screws (16)4. 5/16″ Flat Washers (16)5. 5/

8EXPLANATION OF OPERATING CONTROLSThe following is an explanation of the operating controls of the Delta 10" Radial Saw. We suggest you study the

9ASSEMBLYTOOLS NEEDED FOR ASSEMBLY AND ADJUSTMENTYour Delta Radial Arm Saw can be assembled and adjusted using a few common hand tools, including:• Ph