Delta 36-650 Bedienerhandbuch

INSTRUCTION MANUAL10" Professional Table Saw(Model 36-650)PART NO. 902113 - 11-22-02Copyright © 2002 Delta MachineryTo learn more about DELTA MAC

10INSTALLING SWITCHAND MOTOR CORD1. Insert switch cord (A) Fig. 13, and motor cord (B)of the switch assembly into the opening (C) under sawtable as sh

11MOTOR TO MOTORMOUNTING PLATEDISCONNECT MACHINE FROM POWERSOURCE.Assemble motor (A) to motor mounting plate (B) as shownin Fig. 16. Align the four mo

12MOTOR PULLEY, PULLEY GUARD, ANDDRIVE BELTDISCONNECT MACHINE FROM POWERSOURCE.1. Remove the motor shaft key that is taped to themotor.2. Insert key (

132. Fig. 28, illustrates the motor cord connected to theswitch assembly.CONNECTING MOTOR CORDTO SWITCH ASSEMBLYDISCONNECT MACHINE FROM POWERSOURCE.1.

14BLADE GUARD ANDSPLITTER ASSEMBLYDISCONNECT MACHINE FROM POWERSOURCE.1. Fasten the rear splitter mounting bracket (A) Fig. 29,to the rear trunnion. A

157. Assemble the blade guard and splitter assembly (G)Fig. 33, between the large washer (C) and the splitterbracket and tighten screw (H) with wrench

1610. Using a straight edge, check to see if the saw bladeis aligned with the rear of the splitter (G), as shown inFig. 37. If alignment is necessary,

173. Before tightening the hardware holding the guide railto the saw table, proceed as follows: Beginning at thetwo sides of the saw table and using a

183. Lower the front of rip fence (B) Fig. 46, onto the frontguide rail (L).4. Lock the rip fence (B) Fig. 46, on the guide rails bypushing down handl

19LOCKING SWITCH INTHE “OFF” POSITIONIMPORTANT: When the tool is not in use, the switch (B)Fig.56, should be locked in the OFF position using apadlock

2Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with

20RAISING AND LOWERINGTHE BLADETo raise the saw blade, loosen lock knob (A) Fig. 58, andturn the blade raising handwheel (B) clockwise. Whenthe blade

21BACKLASH ADJUSTMENTSFOR BLADE RAISING ANDBLADE TILTINGMECHANISMSIf any play is detected in the blade raising or blade tiltingmechanisms, the followi

225. Depending on the type of saw blade being used, thecursor (D) Fig. 64, may need adjustment to compensatefor the blade thickness.To adjust the curs

23ADJUSTING TABLE INSERTDISCONNECT MACHINE FROM POWERSOURCE.Place a straight edge across the table at both ends ofthe table insert as shown in Fig. 68

24OPERATIONSCommon sawing operations include ripping and crosscutting plus a few other standard operations of a fundamentalnature. As with all power t

25RIPPINGRipping is the operation of making a lengthwise cutthrough a board, as shown in Fig. 82, and the rip fence (A)is used to position and guide t

26For certain cutting operations such asdadoing and moulding where you are not cuttingcompletely through the workpiece, the blade guard andsplitter as

27USING ACCESSORY DADO HEADTHE BLADE GUARD AND SPLITTERASSEMBLY CANNOT BE USED WHEN DADOING ORMOULDING AND MUST BE REMOVED OR SWUNGTO THE REAR OF THE

28USING AUXILIARY WOODFACING ON RIP FENCEIt is necessary when performing specialoperations such as moulding to add wood facing (A) Fig.94, to one or b

29PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1

317. REDUCE THE RISK OF UNINTENTIONAL STARTING.Make sure switch is in “OFF” position before plugging inpower cord. In the event of a power failure, mo

30Printed in U.S.A.Two Year Limited WarrantyDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, or machin

NOTES31

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

4POWER CONNECTIONSA separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected

Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extensioncord which has a 3-prong grounding type plug a

610" PROFESSIONAL TABLE SAW PARTSFig. 21. Table Saw2. Extension Wing (2)3. Motor4. Pulley Guard Plate5. Switch Assembly6. Lock Knob (2)7. Handwhe

1. Leg (4)2. Bracket 24" Long (2)3. Bracket 21" Long (2)4. Top Bracket (1)5. Plastic Foot (4)Fig. 4STAND PARTS7HARDWARE1. 7/16-20x3/4"

ASSEMBLYSTAND LEGS1. Assemble the longer bottom bracket (A) Fig. 6, tothe inside of two table legs (B) as shown. Align the holesin the longer bottom b

94. WITH A MINIMUM OF TWO PEOPLE,CAREFULLY TURN THE SAW AND STAND UPRIGHTAS SHOWN IN FIG. 10. Carefully push down on the topof the saw until the stand