Delta 31-735 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Schleifmaschinen Delta 31-735 herunter. Delta 31-735 Instruction manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 28
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
INSTRUCTION MANUAL
6" Belt and 12" Disc
Abrasive Finishing Machine
(Model 31-735)
PART NO. 913180 - 10-13-03
Copyright © 2003 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
For Parts, Service, Warranty or other Assistance,
please call
1-800-223-7278 (In Canada call 1-800-463-3582).
Seitenansicht 0
1 2 3 4 5 6 ... 27 28

Inhaltsverzeichnis

Seite 1 - Abrasive Finishing Machine

INSTRUCTION MANUAL6" Belt and 12" DiscAbrasive Finishing Machine(Model 31-735)PART NO. 913180 - 10-13-03Copyright © 2003 Delta MachineryTo l

Seite 2 - GENERAL SAFETY RULES

10DUST BAFFLE1. DISCONNECT MACHINE FROM POWER SOURCE.2. Remove the two screws (A) Fig. 3, and loosen thetwo screws (B).3. Remove the back cover of the

Seite 3

11BELT / DISC SANDER TO CABINETTHE BELT / DISC SANDER IS HEAVY,USE TWO OR MORE PEOPLE WHENPLACING THE BELT / DISC SANDERON TOP OF THE CABINET.1. DISCO

Seite 4 - ADDITIONAL SAFETY RULES

12BELT TO MOTOR1. DISCONNECT MACHINE FROM POWER SOURCE.2. Remove the two screws (A) Fig. 12, on top of thedisc sander and remove plate (B).Fig. 12Fig.

Seite 5 - GROUNDING INSTRUCTIONS

13DUST CHUTE1. DISCONNECT MACHINE FROM POWER SOURCE.2. Insert the dust chute (A) Fig. 16, through the insidehole of the cabinet back panel (B) that wa

Seite 6 - FUNCTIONAL DESCRIPTION

14BELT SANDER TABLE1. DISCONNECT MACHINE FROM POWER SOURCE.2. Thread a 3/8-16 lock nut (A) Fig. 21, onto a 3/8-16x3½" stud (B).NOTE: THREAD LOCK

Seite 7 - CARTON CONTENTS

15DISC SANDER TABLE AND POINTER1. DISCONNECT MACHINE FROM POWER SOURCE.2. Thread the 7/16x3" disc sanding table studs (A) Fig.25, into the side o

Seite 8 - ASSEMBLY

16ABRASIVE DISC1. DISCONNECT MACHINE FROM POWER SOURCE.2. Make certain the disc assembly (A) Fig. 30, is clean,dry, and free of any oil or grease.3. S

Seite 9

17OPERATING CONTROLS AND ADJUSTMENTSSTARTING AND STOPPINGTHE ABRASIVE FINISHINGMACHINETo start the machine, push “START” button (A) Fig. 35. Tostop th

Seite 10 - DUST BAFFLE

184. Rotate the belt by hand, and tighten or loosentracking knob (E) Fig. 39, until the belt is running true onthe pulleys.Fig. 395. Jog the machine o

Seite 11 - INTAKE HOSE

19MITER GAUGE SLOT ONBELT SANDER TABLEPARALLEL TO SANDING BELT1. DISCONNECT MACHINE FROM POWER SOURCE.2. Position the table (A) (Figs. 43 and 44) 90 d

Seite 12 - BELT TO MOTOR

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

Seite 13 - OUTTAKE HOSE

SANDING DISC TABLE 90DEGREES TO DISC1. DISCONNECT MACHINE FROM POWER SOURCE.2. Loosen the two disc table lock handles, the left oneis shown at (A) Fig

Seite 14 - BELT SANDER TABLE

21DUST PORT COVERThe abrasive finishing machine is equipped with amanually operated dust port cover (A) Fig. 52, whichmust be adjusted to suit the san

Seite 15 - AND POINTER

22SANDING INSIDE CURVES2. Loosen the two lock knobs (A) Fig. 37, and removethe top cover (B).3. Inside curves can be sanded on the top sandingdrum, as

Seite 16 - DUST COLLECTOR BAG

23END SANDINGWITH THE BELTWhen sanding the ends of wide workpiecesit is moreconvenient to use the sanding belt with the sanding armin the vertical pos

Seite 17

24CIRCLE SANDING WITH DISC1. DISCONNECT MACHINE FROM POWER SOURCE.A circle sanding attachment is supplied with the sander.It enables the operator to s

Seite 18 - DEGREES TO BELT

25MAINTENANCEREPLACING SANDING BELT1. DISCONNECT MACHINE FROM POWER SOURCE.2. Loosen the two lock knobs (A) Fig. 64, and removethe top cover (B).Fig.

Seite 19 - SANDING ARM

26OVERLOAD PROTECTIONThe motor supplied with your sander is equipped with areset overload relay button (A) Fig. 67. If the motor shutsoff or fails to

Seite 20

27PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

Seite 21 - OPERATIONS

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

Seite 22 - SANDING BELT

3FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.1. FOR YOUR OWN SAFETY, READ THE INSTRUC-TION MANUAL BEFORE OPERATING THEMACHINE.

Seite 23 - WITH THE DISC

4FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.SAVE THESE INSTRUCTIONS. Refer to them often and use them to instruct others.ADDI

Seite 24 - CIRCLE SANDING WITH DISC

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

Seite 25 - MAINTENANCE

6Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong grounding type plug

Seite 26 - ACCESSORIES

7CARTON CONTENTS12346578910111. Cabinet2. Dust Baffle3. Bag Hanger4. Dust Chute5. Dust Bag6. Hose (2)7. Hose Clamp (5)8. Belt / Disc Sander9. Belt San

Seite 27

8ASSEMBLYFOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTILTHE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE

Seite 28 - • DELTA)

9Fig. 2EFig. 2DFig. 2F7. Insert a 5/16-18x4" hex head screw (G) Fig. 2D,through the hole (F) Fig. 2C, in the pivot bracket, the twoholes (E) in t

Kommentare zu diesen Handbüchern

Keine Kommentare