Delta 14-070 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Bohrmaschinen Delta 14-070 herunter. Delta 14-070 Instruction manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken

Inhaltsverzeichnis

Seite 1 - 14"

INSTRUCTION MANUAL14" Floor DrillPressPART NO. 1046995© Delta Machinery International Machinery Corp. 1995MODEL 14-070Dated 6-30-95

Seite 2 - TABLE OF CONTENTS

1. Drill two 3/8" diameter holes (C) Fig. 12B, correspon-ding to the mounting holes (A) Fig. 12A, of the drill press basein a 21" by 28"

Seite 3 - SAFETY RULES

CAUTION: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRICSHOCK.In the event of a malfunction or breakdown, grounding prov

Seite 4 - FOR DRILL PRESSES

SPINDLE SPEEDSTwelve spindle speeds of 250, 360, 410, 540, 590, 650,1090, 1280, 1450, 1820, 2180 and 3000 RPM are avail-able with the 14" Drill P

Seite 5 - UNPACKING

CHANGING SPINDLE SPEEDSAND ADJUSTING BELT TENSION1. DISCONNECT THE DRILL PRESS FROM THE POWER SOURCE.2. Lift up belt and pulley guard (A) Fig. 16.3. L

Seite 6 - ASSEMBLY INSTRUCTIONS

SWITCHThe switch (A) Fig. 17, is located on the front of the drillpress head. To turn the drill press “ON” move the switchto the up position. To turn

Seite 7

3. The table can be tilted right or left by pulling out andremoving table alignment pin (C) Fig. 20, and loosening table lock-ing bolt (D). NOTE: If p

Seite 8

DRILLING HOLESTO DEPTHWhere a number of holes are to be drilled to exactly thesame depth, a depth stop is provided in the pinion shafthousing and is u

Seite 9 - TO A SUPPORTING SURFACE

OPERATIONYour drill press is to be used with drill bits of 5/8" or less indiameter. The following directions will give the inexperi-enced operato

Seite 10 - ELECTRICAL REQUIREMENTS

Two Year Limited WarrantyDelta MachineryDelta will repair or replace, at its expense and at its option, any Delta machine, machine part, ormachine acc

Seite 11 - GROUNDING INSTRUCTIONS

TABLE OF CONTENTSSAFETY RULES 3ADDITIONAL SAFETY RULES FOR DRILL PRESSES 4UNPACKING 5CLEANING 6ASSEMBLY INSTRUCTIONS 6-9FASTENING DRILL PRESS TO A SUP

Seite 12 - SPINDLE SPEEDS

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with t

Seite 13 - AND ADJUSTING BELT TENSION

ADDITIONAL SAFETY RULESFOR DRILL PRESSES1. WARNING: DO NOT operate your drill press until it iscompletely assembled and installed according to theinst

Seite 14 - THE “OFF” POSITION

UNPACKINGCarefully unpack the drill press and all loose items from the carton. Figure 2 illustrates the drill press and all loose itemssupplied with t

Seite 15

CLEANINGRemove the protective coating from the machined surfaces of the drill press and all loose items. This coating may beremoved with a soft cloth

Seite 16 - RETURN SPRING

4. Insert raising rack (E) Fig. 5, which was removedin STEP 2, into groove in table bracket (H) makingsure gear inside table bracket is engaged with t

Seite 17 - OPERATION

7. Assemble table raising and lowering handle (M) Fig.8, to shaft on table bracket and tighten set screw in han-dle against flat on shaft.8. Thread ta

Seite 18 - Delta Machinery

11. IMPORTANT: Make certain the bottom ofspindle (S) Fig. 11, and tapered hole (T) in chuckare clean and free of any grease, lacquer or rustpreventive

Kommentare zu diesen Handbüchern

Keine Kommentare